Click image above to view Installation Instructions

Warning: Installing this product requires Welding and Fabrication skills, If youare not confident in your abilities to complete this task please have thisinstalled at an qualified off-road shop .

While we're working on the detailed instructions, here'ssome tips on installing your APEX 1ton swap truss. Refer to online pictures fororientation of the truss.

Step 1.

Inventory all parts to ensure you have all of the correctpieces. If youare missing parts or the package is damaged Contact Artec Industries Immediately at (855) 278-3299  M-F 8:30-5pm MST If outside of those hoursEmail us at Sales@Artecindustries.com (Please include picture of part numberlabel on box as well as your invoice number Also keep the box and take picturesof the box per shipping carrier for a damage claim otherwise it could be denied)

STEP 2.

 Remove OEM bracketryfrom axle. Take care not to grind into the axle tube. Remove rust or paint ontop of casting and axle tubes using a flap disc or wire wheel. Remove factorybreather hose and barbed fitting from casting. Super duty axle swap kitsrequire some trimming of the factory casting in order to mount all the requiredcomponents on the driver side axle tube. once the trimming of the axle tube is completed Weld the driver sideaxle tube to the newly cut back casting. 

( For Super duty Axles Please see  Step 2A for reference in this link of whatneeds to be removed from the casting which will be highlighted in blue : https://www.artecindustries.com/assets/images/Company/documents/JK6010-install.pdf)

Step 3.

Once The axle is clean of all factory bracketry  Insert the JL6540-18 & 19 Gussets intothe Keyed slots on JL6540-1  (the -19 Part will go closest to the end)    Now Place the Jl6540-1  Onto the Long tube of the axle and slide overuntil the edges make contact with the diff housing. This will clock the trussinto position so the Upper control arms will be set into their proper positionwhen they are added to the truss in later steps.

Step 4.

Slip the Jl6540-4 onto the Jl6540-2 the edges of the coilbucket will slip into the slot .  thenplace on the Passenger side Axle tube between the truss and the C for theknuckle  making sure all of the edges areinline and flush

(You can rotate the Spring bucketforward and back if you want to adjust for more or less pinion angle  for your build)

Step 5.

Place JL6540-3 between the casting and C for knuckle on the driverside tube then set Jl6540-5 onto Jl6540-3 the Relief cut will face the front of the Jeep that is for it to clear thetrack bar on the frame side

(If you need to rotate for pinion angle you can grind downthe 2 fins that sit on top of the casting on JL6540-3)

Step 6.

Place Jl6540-6 on top of JL6540-4  the tab will Jig into a hole  then set Jl6540-8 on top of Jl6540-6    Repeat this step on the driver side with Partnumbers JL6540-7 &Jl6540-9 Tack well all of the brackets and truss piecesinto place.

Step 7.

Slip JL6540-10 under JL6540-4 the tab will sit into the holeand tack into place Repeat this step on the driver side with JL6540-5 &JL6540-11

Step 8.

Slip JL6540-17 into JL6540-16   then Roll up onto the axle there is a keyway on the -16 bracket that will slip onto the JL6540-4 to locate it on theaxle once it is in position tack weld into place

(JL/JT Jeeps will want the track barbracket as far to the outside of the axle as the bracket will allow JK's willhave the bracket slid over towards the center some But if you have anAdjustable track bar that will allow the additional length you can use theJL/LT placement for a longer track bar)

Step 9.

Place Jl6540-15 on the back side of the axle the tall wingwill slip into a tab under JL6540-2 closest to the C ,Tack weld into position.  Repeat on the Driver side with  JL6540-14 and JL6540-5    Then Place JL6540-12 into the 2 remainingslots on the backside of the coil mount and tack into position    Completethis step with doing the same for the driver side with JL6540-13

Step 10. 

Place the Passenger side Upper control arm mount on top ofthe Jl6540-1  it will Jig into place thentack weld into position.  

Step 11.

Fully weld all of the components together .  Be sure to move around on the truss so you donot work in the same area to decrease the chances of warping the axle . 

( Steps 12-14  are forthe  4 link Truss Options only ! For3link Options Continue to Step 15 )

Step 12: 

Place the JL6501 top cap on top of the differential to makesure the cap sits flat between the driver side spring perch and side of theJl6540-1 truss, You will use the rear hole on the top cap and center the port for the breather .     Using a marker mark areas on the housingwhere the Top cap may contact    (someaxles have a little finger on the top of the diff that needs to be groundflush  and some have a little lip on thepinion side of the casting that needs to be shaved down .   Once you have the top cap sitting level onthe Truss and coil mount tack weld into position . 

Step 13.

Assemble the Upper link mount and insert it into the Tabs onthe top cap and tack weld into position.

Step 14.

Finish welding the top cap onto the Housing,  Truss , and coil buckets followed by theupper control arm mounts.

Step 15.

Wrap in a welding blanket to cool slowly overnight.

Step 16:

Paint or Powder coat the bare surfaces.