• MON-FRI 9am-5pm MDT • GET DIRECTIONS
  • Installation Instructions

    Test Product

    Part Number:

    • JL5625

    Difficulty

    Time Required

    Install Time3-4 hours

    Skills Required

    • Basic Mechanics
    • Welding
    • Electrical
    • Fabrication

    Bill of Materials

    Install Video

    Tools Needed

    • T30 Torx Driver
    • 10mm Socket/Wrench
    • Torque Wrench
    • Thin Ratchet Strap
    • 7/32 Allen Wrench

    Related Products

    (2-PACK) - LED Bolt lights - 3 watt, Stainless Steel, 11mm, Silver
    (2-PACK) - LED Bolt lights - 3 watt, Stainless Steel, 11mm, Silver
    (2-PACK) - LED Bolt lights - 3 watt, Stainless Steel, 11mm, Silver
    (2-PACK) - LED Bolt lights - 3 watt, Stainless Steel, 11mm, Silver
    (2-PACK) - LED Bolt lights - 3 watt, Stainless Steel, 11mm, Silver
    (2-PACK) - LED Bolt lights - 3 watt, Stainless Steel, 11mm, Silver

    (2-PACK) - LED Bolt lights - 3 watt, Stainless Steel, 11mm, Silver

    $49.99
    (4-PACK) - LED Bolt lights - 3 watt, Stainless Steel, 11mm, Silver
    (4-PACK) - LED Bolt lights - 3 watt, Stainless Steel, 11mm, Silver
    (4-PACK) - LED Bolt lights - 3 watt, Stainless Steel, 11mm, Silver
    (4-PACK) - LED Bolt lights - 3 watt, Stainless Steel, 11mm, Silver
    (4-PACK) - LED Bolt lights - 3 watt, Stainless Steel, 11mm, Silver
    (4-PACK) - LED Bolt lights - 3 watt, Stainless Steel, 11mm, Silver

    (4-PACK) - LED Bolt lights - 3 watt, Stainless Steel, 11mm, Silver

    $89.99
    1 TON - APEX Front 60 Differential Top Cap 1985-1997
    shown in JL6531
    1 TON - APEX Front 60 Differential Top Cap 1985-1997
    shown in JL6531

    1 TON - APEX Front 60 Differential Top Cap 1985-1997

    $69.99

    Prior to beginning vehicle tear down and install, check all contents in the box against the Bill of Materials (BOM) to ensure the product is complete.

    Additional support is available at sales@artecindustries.com or 855-278-3299 M-F 9am-5pm MST

    Introduction

    Thank you for your purchase of our Bellypan Kit designed to protect the underside of your JL Jeep Wrangler. All the pieces of this bellypan are designed to fit very closely to each other for a simple and precise assembly. If you have any questions that are not answered in these instructions, contact us at sales@artecindustries.com.

    Consumer Warning

    All Artec Industries products must be installed by a competent and qualified individual in accordance with the installation instructions intended for the product. Incorrectly installed products will void any warranties and may result in damage to the product or damage to the vehicle it was installed on. Read any provided instructions or guides and watch any available videos before attempting installation. If there are any questions, please contact Artec Industries before starting installation.

    Many products require the vehicle be properly raised and supported off the ground. The installer is responsible for confirming that this may be done in a safe manner and the correct equipment is available to perform the installation. Artec Industries installation instructions assume the installer is able to properly and safely lift the vehicle.

    Vehicles that have been modified will not perform the same as a stock vehicle. It is incumbent upon the owner of the vehicle to be aware of the differences the modifications will make to the driving characteristics of the vehicle. These may include (but are not limited to): changes in handling, braking, rollover angle, incompatibilities with the factory anti-lock braking systems, stability control systems, or traction control systems.

    Any additional warnings specific to the product can be put here. Other information can be included in the notes below. Hopefully this note will wrap properly in the paragraph on pagefly.

    Here is another paragraph just for testing purposes. I think that this test should be long enough to make sure everything is working properly.

    Notes

    These are just some general notes for the customer. Don't do anything stupid.

    Introduction

    This guide will walk through the correct installation procedure for the 

    Consumer Warning

    All Artec Industries products must be installed by a competent and qualified individual in accordance with the installation instructions intended for the product. Incorrectly installed products will void any warranties and may result in damage to the product or damage to the vehicle it was installed on. Read any provided instructions or guides and watch any available videos before attempting installation. If there are any questions, please contact Artec Industries before starting installation.

     Many products require the vehicle be properly raised and supported off the ground. The installer is responsible for confirming that this may be done in a safe manner and the correct equipment is available to perform the installation. Artec Industries installation instructions assume the installer is able to properly and safely lift the vehicle.

    Vehicles that have been modified will not perform the same as a stock vehicle. It is incumbent upon the owner of the vehicle to be aware of the differences the modifications will make to the driving characteristics of the vehicle. These may include (but are not limited to): changes in handling, braking, rollover angle, incompatibilities with the factory anti-lock braking systems, stability control systems, or traction control systems.

    Notes:

    This installation requires 

    Step 1

    Included Parts

    Conclusion

    Installation is complete!

    With any modified vehicle, or any vehicle used offroad, it is a good idea to check bolt torques periodically and visually inspect components regularly.

    Write A Product Review
    Post Comment

    YOUR CART (0)

    No Products in the Cart